Redmi phone does not turn on and shows the Android logo: step-by-step guide

If the Redmi phone does not turn on and endlessly shows the Android logo or Mi instead of booting the system, this is a clear sign of a failure known as a “bootlap”, which requires immediate diagnostics to eliminate software errors or identify hardware faults.

There is no need to panic. In most cases, the problem can be solved at home without contacting a service center. However, it is important to consistently check all possible causes, ranging from simple system freezes to complex memory problems. If the Redmi phone does not turn on, but only shows a boot animation, this is a signal that the operating system cannot correctly complete the initialization of components.

Below we will analyze in detail the algorithms of actions that will help bring the device back to life. We will look at methods from a simple reboot to a full factory reset and flashing. Remember that some actions can lead to data loss, so carefully follow the instructions and assess the risks before starting work.

Causes of the logo stuck on loading

Before taking active steps, you need to understand the nature of the problem. If the Redmi phone does not turn on and shows Android, this means that the bootloader is working, but the operating system itself “crashes” during the initialization stage.

Most often, the culprit is an unsuccessful software update or a faulty system file. Problems may also arise after installing custom recovery or modified firmware. Sometimes the reason is a full internal memory, which does not leave the system space for temporary files.

Xiaomi breakdown statistics

According to service centers, about 60% of cases of freezing on the Redmi logo are associated with software failures after an update, 25% with a faulty flash memory and 15% - with a low battery or power problems.

Hardware reasons are less common, but they are more serious. This could be a failure of the power controller or degradation of the drive eMMC. If the device has been dropped or fallen into water, the likelihood of hardware failure increases many times over.

⚠️ Attention! If the phone made strange sounds, got very hot, or fell before the logo appeared, there is a high probability of physical damage. In such cases, independent attempts to flash the firmware can aggravate the situation.

Primary diagnostics and forced reboot

The simplest and safest method that is worth trying first is a forced reboot. Sometimes the system simply “gets stuck” in a cycle, and a hard power reset helps it get out of this state.

To do this, you need to hold down the power button and hold it for a long time. On different Redmi models, the holding time may vary, but usually 10-15 seconds is enough. If the screen goes dark and vibration appears, release the button and wait for the normal boot.

• 🔋 Make sure the battery charge is at least 15-20%, connect the charger for 10 minutes before attempting to reboot.
• 🔄 Press the button combination Volume Down + Power simultaneously for 15-20 seconds.
• 📱 If the first combination does not work, try holding down only the button Power for 30 seconds.

If the Redmi phone does not turn on after these manipulations and shows Android again, proceed to the next steps. You should not reboot endlessly, this can drain the battery to zero, which will complicate diagnostics.

Entering Recovery mode and resetting settings

If a soft reboot did not help, you need to use the built-in recovery mode - Recovery Mode. This is a special diagnostic interface that allows you to control the system bypassing the main bootloader.

To enter this mode on Xiaomi and Redmi smartphones, a specific key combination is used. The device must be completely turned off. If it is stuck on the logo, wait until the battery drains or use the forced shutdown described above.

Volume Up + Power

Press these two buttons at the same time and hold until the logo appears Mi. As soon as it appears, release the Power button, but continue to hold the Volume Up button until the Recovery menu appears.

In the menu, navigation is done using the Volume buttons (up/down), and selecting an item is done using the Power button. You need to find the section Wipe Data and select the option Wipe All Data. This action will delete all user data, returning the phone to its factory state.

⚠️ Attention! Procedure Wipe Data completely deletes photos, contacts, messages and installed applications. It will be impossible to restore the data without a prior cloud backup.

After confirming the reset, the phone will begin the cleaning process. When finished, select Reboot, and then Reboot to System. The first boot after a reset may take up to 5-10 minutes, as the system reinitializes the files.

Diagnostics via Fastboot mode

If resetting the settings did not solve the problem and the Redmi phone still does not turn on, showing Android, it is worth checking the status of the bootloader via the mode Fastboot. This mode allows you to interact with the device at a low level through a computer.

To enter Fastboot, hold down the buttons Volume Down + Power on the switched off device. Hold them until the image of a hare repairing an android appears on the screen, or the inscription FASTBOOT.

Connect the phone to the computer using a working USB cable. If the utility Mi Flash Tool or ADB/Fastbootis installed on your PC, you can check the connection status. In the computer command line, enter the command:

fastboot devices

If you receive a device serial number in response, it means there is a connection with the bootloader and the hardware is most likely working. This opens the way to flashing.

The lack of reaction from the computer may indicate a problem with the phone's charging port, cable, or a critical malfunction of the motherboard. In this case, further software actions are useless.

Complete flashing of the device via Mi Flash

The most radical but effective way to save the phone is a complete flashing. For Redmi phones, this is done using the official utility Mi Flash Tool and downloaded firmware in the format Fastboot (.tgz extension).

You will need to download the firmware specifically for your model. It is important not to confuse the versions for China and the Global version, and also not to try to flash the old version over the new one without unlocking the bootloader.

Firmware type	File extension	Installation method	Data saving
Recovery (OTA)	.zip	Through the Recovery menu	Possible
Fastboot	.tgz	Via Mi Flash Tool	No (full reset)
EDL (9008)	.xml / .elf	Through test points / authorized account	No

The firmware process is as follows: unpack the archive with the firmware to the root of the disk (the path should not contain Cyrillic), run Mi Flash, connect the phone in Fastboot mode and press the button Refresh.

In the lower right corner of the utility, select mode clean all (full cleaning). Do not select clean all and lockif you are not sure about the firmware region, otherwise you may block the bootloader forever. Press Flash and wait for the process to complete, which will take from 200 to 600 seconds.

Hardware faults and EDL mode

If all software methods have been exhausted, and the Redmi phone does not turn on and shows Android or a black screen, the problem lies in the hardware. Often the culprit is degradation of the memory chip or failure of the processor due to overheating.

In such cases, the device can only be detected by the computer in EDL (Emergency Download Mode). In Windows Device Manager it will appear as Qualcomm HS-USB QDLoader 9008. Entering this mode on modern Xiaomi often requires disassembling the phone and short-circuiting special test points on the board.

Firmware in EDL mode requires an authorized Xiaomi account with engineer rights, which ordinary users cannot obtain. Therefore, when the device enters this mode without the ability to exit, the only solution is to contact a specialized service center.

⚠️ Attention! An independent attempt to open the case and close the contacts without experience can lead to a short circuit and the final death of the motherboard. Entrust the work to professionals.

It is also worth checking the battery. If the battery is older than 3 years, it could have lost capacity and not produce the required current to start the processor, which is why the phone goes into an endless reboot immediately after the logo appears.

Frequently asked questions (FAQ)

Is it possible to recover data if the phone hangs on the logo?

Unfortunately, if solving the problem requires entering Recovery mode with the option Wipe Data or flashing via Fastboot, all data will be permanently deleted. There is a chance only if you can log in through safe mode (if such an option is available in your version of MIUI) or through ADB with superuser rights, which is unlikely with a bootloop.

The phone turns on only when connected to charging, what should you do?

This is a clear sign of a faulty battery or power controller. The battery does not support the load when the system starts. Try replacing the battery. If the problem persists, a diagnosis of the power circuit on the motherboard is required.

Does removing the SIM card and memory card help with the freeze?

Yes, in some cases, a damaged MicroSD memory card or a faulty SIM card can cause a conflict when booting the system. Try removing them and turning on the phone without them. If the device boots, the problem is in one of the extracted modules.

Why did the phone stop turning on after the MIUI update?

Errors during OTA updates (over the air) occur due to interrupted communication, lack of memory space or system file conflicts. In this case, the most effective solution is to completely flash the device through a computer using the Fastboot image.

How long can the first boot take after a reset?

After executing the command Wipe All Data the first boot can take from 5 to 15 minutes. During this time, the Android or Mi logo may remain on the screen. Do not try to reboot the phone during this period, let the system finish optimizing applications.